Mercedes S-Class W-140

1991-1999 of release

Repair and operation of the car



Mercedes S-Class
+ Mercedes-Benz cars of the class S (W-140)
+ Operation manual
+ Routine maintenance
- Engine
   Check of a compression in engine cylinders
   Check of the engine by means of the vacuum gage
   Belt of the streaming drive of auxiliary units
   + 6-cylinder petrol engines (M104.944 and M104.990/994)
   + 8-cylinder petrol engines (M119.970/981 and M119.971/981)
   - 12-cylinder petrol engines (M120.980/982)
      The air cleaner - installation details
      Covers of heads of the block of cylinders
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
      The valve of recirculation of the fulfilled gases - installation details
      Air supply pump
      Removal and installation of the top forward covers
      Heads of the block of cylinders
      Removal and installation of a cover of a chain of the GRM drive
      Replacement of a chain of the GRM drive
      The GRM drive - the general information, service of components
      Natyazhitel of a GRM drive chain
      Camshaft regulator
      Removal and installation of camshafts
      Check of phases of gas distribution
      Check and adjustment of position of camshafts
      Replacement of the directing plugs of valves
      Measurement of diameters of cylinders
      Removal and installation of pistons
      Check of rods
      Removal and installation of a bent shaft
      Removal and installation of the pallet of a case of the engine
      The oil level sensor switch - installation details
      The oil pump - a design and details of installation
   + 6-cylinder diesel engines (OM603.971)
   + 6-cylinder diesel engines (OM606.961)
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Gear shifting box
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


79c5991e

Check of phases of gas distribution

Phases of gas distribution of the engine of the M120.980 series

Check digital designation of camshafts. Codes are beaten out on a neck of the 3rd bearing or on a flange

Inlet camshafts

 PERFORMANCE ORDER

1. Turn a bent shaft by means of a key so that noses of cams of inlet camshafts were directed up.

2. Establish a clamp (2) of the dial measuring instrument with the carving plug (4) on a sealing surface of a cover of a head of the block of cylinders of the checked camshaft of cylinders (1) or (7).
3. Attach the dial measuring instrument (1) with a rod (3) (80 mm) on a clamp (2) so that the rod (3) was established vertically on the hydrocompensator (shooter) with a tightness of 3 mm.
4. Check ease of movement of a rod (3).
5. Establish an arrow the dial measuring instrument (1) in "0".
6. Rotate a bent shaft a key in the direction of rotation of the engine until the measuring instrument (1) does not show raising of the valve on 2 mm. In this situation check "the angle of opening of the inlet valve after VMT" on a damper of tortional fluctuations.

Final camshafts

 PERFORMANCE ORDER

1. Turn a bent shaft by means of a key so that noses of cams of final camshafts were directed up.
2. Establish a clamp (2) of the dial measuring instrument with the carving plug (4) on a sealing surface of a cover of a head of the block of cylinders of the checked camshaft of cylinders (1) or (7).
3. Attach the dial measuring instrument (1) with a rod (3) (80 mm) on a clamp (2) so that the rod (3) was established vertically on the hydrocompensator (shooter) with a tightness of 3 mm.
4. Check ease of movement of a rod (3).
5. Establish an arrow of the measuring instrument (1) in "0".
6. Rotate a bent shaft a key in the direction of rotation of the engine until the measuring instrument does not show raising of the valve on 2 mm. In this situation check "the angle of opening of the final valve before NMT" on a damper of tortional fluctuations.