Mercedes S-Class W-140

1991-1999 of release

Repair and operation of the car

Mercedes S-Class
+ Mercedes-Benz cars of the class S (W-140)
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Gear shifting box
- Automatic transmission
   Specifications
   Search of malfunctions - the general information
   - Automatic transmission 722.5
      Removal, check of a state and installation of the converter of rotation (hydrotransformer)
      Removal and installation of the centrifugal regulator
      Removal and installation of the sensor switch of blocking of a starter (permission of start)
      Vacuum knot - installation details
      Removal, service and installation of the secondary pump (AT to No. 3652931)
      Removal and installation of a forward cover with the secondary pump
      Removal and installation of the LB3 piston
      Removal and installation of a back cover of transmission
      Dismantling and assembly of valvate assembly of AT
      Dismantling and assembly of transmission
      Installation and check of a gap in a multidisk brake of B3
      Measurement of a gap in B1 brake
      Coupling of the raising transfer
      Removal, installation and check of components of a brake of BS of the raising transfer and coupling of KS
      Dismantling and assembly of the coupling of a free wheeling
      Dismantling and assembly of planetary mechanisms
      Dismantling and assembly of coupling of K1
      Coupling of K2
      Gear shifting selector lever
   + Automatic transmission 722.6
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Coupling of the raising transfer

Dismantling

Design of coupling of the raising transfer


172 — the Support of multidisk coupling 174, 179 — Lock rings 180 — the Spring disk 181, 185 — Radial epiploons	182 — Pruzhina 183 — the Piston 184 — the Sealing ring 02 — the Stripper

PERFORMANCE ORDER

1. Remove a lock ring (174) from a support of multidisk coupling (172).
2. Remove the block of disks (176) - (178) and a disk spring (175).
3. Establish a stripper (020) on a spring plate (180) so that the lock ring (179) opened.
4. Remove a spring plate (180), a spring (182), a radial epiploon (181).
5. Take the piston (183) from an external support of coupling (172).

Assembly and measurement of a gap in coupling of the raising transfer

Coupling assembled


172 — the Support of multidisk coupling 179 — the Lock ring 180 — the Spring disk 181, 185 — the Radial epiploon	182 — Pruzhina 183 — the Piston 184 — the Sealing ring

PERFORMANCE ORDER

1. Insert the plug (023) into a support of coupling (172). Check a radial epiploon (185) and a sealing ring (184) for lack of wear, and if it is necessary, replace and grease them with transmission liquid. At assembly be convinced that edges of epiploons (181) and (183) are located up. 2. Insert the piston (183). 3. Remove the plug (023).
4. Insert everything 18 or 19 springs (182) into a guide of the piston (183). 5. Insert the plug (024) into a support of coupling (172). 6. Grease an epiploon (131) with transmission liquid and establish on a spring plate (180). 7. Fix a spring plate (180).
8. Establish a lock ring (179) on a spring plate. Establish and fix a stripper (020). Insert a lock ring (179). Be convinced of correctness of installation.

Order of installation of clutch plates


174 — the Lock ring 176 — the Disk spring 178 — Internal disks 177, 178 — External disks

PERFORMANCE ORDER

1. Disconnect and remove a stripper (020). Establish clutch plates in the order specified on an accompanying illustration and insert in turn. Before installation put new disks in transmission liquid approximately for 1 hour.
2. Remove the plug (024).
3. Measure a gap of "S" and adjust it a lock ring (174) if it is necessary. Thickness of a lock ring of 2.0, 2.5, 3.0 and 3.5 mm.